您要查找的是不是：
- pure bending test 纯弯试验
- According to the original assumption, this theory should be applied only to long, thin beams loaded in pure bending. 根据原来的假定，这个理论只适用于受纯弯曲载荷的长而薄的梁。
- These formulae give us the stress and strain in a prismatic beam when it is subjected to pure bending. 当棱柱形梁受纯弯曲时,这些公式给出了它的主力和主变。
- In a beam type compensator a stress pattern produced by pure bending is frozen into the material. 在梁式补偿器中,其应力光图是由纯弯曲产生而被冻结在材料之中。
- These formulas give us the stress and strain in a prismatic beam when it subjected to pure bending. 当棱柱形梁受纯弯曲时，这些公式给出了它的主力和主变。
- The structure,cold bending fraction pattern and EXD of Q235 plate cold bending test sample of Shanghai Meishan Company are analyzed. 对梅山公司Q235冷弯不合格试样进行了金相组织、冷弯断口形貌及能谱分析。
- The flexural strength of all FRC posts was tested with a 3-point bending test. 三点挠曲实验比较不同弯曲度的FRC弯钉与FRC直钉的挠曲强度和挠曲模量。
- The Test of Combination Beam Pure Bending Stress 叠层梁纯弯曲正应力实验
- Application: Road profile rotating bending test on wheel hubs with simulation of wheel load and lateral forces. 应用范围：公路概况与旋转弯曲载荷和车轮的侧向力轮毂模拟试验。
- Meanwhile, the springback potential energy principle is applied to calculate the springback deformation of a pure bending of curved beam. 同时，应用该回弹势能原理于纯弯曲梁的回弹变形计算。
- Furthmore, EFPI and FBG sensors embedded inside FOSL are performed by using the four-point bending test. 在此基础上，对FOSL试件中的EFPI和FBG传感器进行了四点弯曲试验。
- A bend test is a simple test for ductility that does not require special equipment, or a specially shaped test-piece. 弯曲试验是测试韧性的简单试验，不要求特别的测试设备，或规定形状的试样。
- The SCF at the bottom of U-shaped notch of three-point bending beam is smaller than that of the counterpart pure bending beam, and the largest relative difference is -7.3%. 将U形切槽梁三点弯曲的应力集中系数与对应的U形切槽梁纯弯曲的应力集中系数作比较，发现前者比后者小，最大相对偏差达到-7.;3%25。
- As there is no criterion or standard about castellated member at home, study of the web stability of castellated be ams under pure bending condition is carried out. 针对国内尚无有关蜂窝构件的规范或标准可以执行的实际情况，进行了蜂窝梁腹板在纯弯状态下的稳定问题研究.;基于薄板的弹性稳定理论，建立了孔口处腹板和孔间处度板的计算模型；
- Metal material bending test is an important item when raw materials come to factory in boiler and pressure vessel manufacturing trade. 金属材料的弯曲试验是锅炉压力容器制造行业进行原材料入厂检验的一项主要检查项目。
- The bending fracture problems of cracked plate for anisotropic functionally graded materials under loads of pure bending, pure twisting or bending and twisting are discussed. 摘要探讨各向异性功能梯度材料裂纹板受纯弯、纯扭、弯扭载荷作用下的弯曲断裂问题。
- In this article tensile test,bending test and microhardness test were conducted on the laser welded joint of the steel sheet for automobile use. 对汽车用薄板的激光焊接接头进行了拉伸试验、弯曲试验及显微硬度分析等。
- In this test, air-dry woods of China-fir, Taiwan acacia, Lauan and Hemlock were used to monitor AB counts under static bending test. 本试验以杉木、相思树、柳桉及铁杉之气乾材为试材，测定静力弯曲试验时AE发生之情况，探讨AE发生次数与应力、应变之关系。
- Moreover, Equation (5.15) predicts ovalisation at maximum bending strain while measurements were performed after the bending test. 此外，等式(5.;15)预测了在挠度测试后度量的基于最大弯曲应变的成椭圆形，
- The method to determine the interlaminar shear strength for composite material is also proposed by five-point bending test, and the experimen... 同时，文中提出了用五点弯曲实验测试层间剪切强度的方法，给出了实验结果。
