该词条未找到_海词词典

您要查找的是不是：

Standard version: output shaft with keyway. 标准产品:输出轴带键槽.;消声器可拆除
Remove the bezel and rubber gasket from the motor output shaft. 从马达输出轴上拆卸玻璃框和橡皮垫圈。
Dynamic Torque : the degree, the role of the output shaft torque. 动态扭矩：在分度期间，作用在出力轴上的最大扭矩。
Stop action : Each output shaft rotation - down a few. 停动数：出力轴每一旋转的停动数。
Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft. 转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。
Output shaft when the swing set in the center of rotation on the trip-down, design may also need to set rotation angles and movements itinerary. 出力轴在摆动时可设定在旋转行程的中心点上停动，也可依设计需要设定旋转角度和升降行程。
Stop: stop rotating output shaft, cam rollers contact roller cam bearings taper ribbed support of the re-direct. 停止：出力轴停止旋转，凸轮滚子接触滚子轴承式凸轮锥度支撑肋的重直部分。
The clutch rotor is fixed on the input shaft and the clutch armature is fixed on the output shaft. 离合器的转子固定在入力轴，而离合器的电极板与刹车被固定在出力轴上。
Direct drive to the rolls with heavy-duty helical bevel gears where the output shaft is directly coupled to the roll shaft. 高坚固的螺旋斜线轴承直接驱动辊筒。输出轴直接连接辊轴，中间没有任何传动消耗。
Output flange is connected with output shaft by a involute spline, and fastened by a locknut. 输出突缘通过渐开线花键与输出轴相连，并用锁紧螺母将其锁住。
The output shaft rotary tables can be used automatically rotating machinery Center momentum. 出力轴上的旋转台可用作自动旋转机器的中心传动力。
Taper support rib usually two or three cam roller contacts, in order to edge into the axis of rotation to be sent to the uniform output shaft. 锥度支撑肋通常与两个或三个凸轮滚子接触，以便入力轴的旋转可均匀地传送到出力轴。
LF200 consists of a 3-shaft helical gear set and a lockable planetary differential gear. its output shaft and input shaft swivel in the same direction. LF200型分动器由三轴式斜齿轮组和带有可锁式轴间行星式差速器组成，其输出轴和输入轴旋向相同。
During reassembly, grease the bore of the drive shaft receiving the reduction gear’s output shaft before reinstallation of the clamp ring. 在重组，油脂的膛的传动轴收到减速器的输出轴之前重新安装钳环。
It introduces a precision and quick way to check proper alignment of rotating reel shaft in ship unloader with the gearbox output shaft. 摘要介绍1种可以高精度、快速测量码头卸船机卷筒旋转轴与齿轮箱输出轴对中的方法。
Aiming at oil leakage phenomenon of transmission output shaft of domestic ZL40/50 loaders, causes of the leakage and countermeasures are expatiated. 摘要针对国产ZL40/50装载机变速器箱输出轴渗漏现象，详细阐述了引起输出轴渗漏的原因及解决的方法。
The low speed shaft features a “no-leak” drywell design that physically separates the oil sump from the output shaft to eliminate gear oil contamination of the tank product. 低速轴的特点是：“无泄漏”的干井式设计，油箱与主轴分离，消除了齿轮油污染槽体内介质的机会。
The low speed shaft features a "no-leak" drywell design that physically separates the oil sump from the output shaft to eliminate gear oil contamination of the tank product. 低速轴的特点是：“无泄漏”的干井式设计，油箱与主轴分离，消除了齿轮油污染槽体内介质的机会。
It is put forward that the multi-labyrinthic sealing and stuffing box sealing are adopted respectively on the input shaft and output shaft of the reducer. 据此,提出了最佳改造方案:减速箱输入轴采用多重式迷宫密封结构,输出轴采用盘根盒密封结构。
Rotating through means of supporting the eccentric shaft housings can be high-power output shaft axis and the distance between completely exclude Sleek phenomenon. 通过旋转支撑入力轴的偏心轴承座可高速入力轴和出力轴之间的距离，能完全排除不滑顺的现象。