您要查找的是不是：
- reliability control algorithm 可靠性控制算法
- Correct control algorithm is the key of network congestion control. 因此,正确的控制算法是网络拥塞控制的关键。
- The control algorithm uses the increase type PID control algorithm. 系统实时性和控制精度较高。
- UDT uses UDP to transfer bulk data with its own reliability control and congestion control mechanisms. UDT建于UDP之上，并引入新的拥塞控制和数据可靠性控制机制。UDT是面向连接的双向的应用层协议。
- So the adaptive character of the control algorithm has been enhanced. 将该算法应用到电控气动离合器操纵系统中并进行实验。
- An intelligence PID control algorithm based on the expert system was discussed. 讨论了一种基于专家知识的智能PID控制算法。
- A reliability control model of grid resource is proposed by samdwich which include facticity enrolling,credit evaluating and scheduling contract. 针对网格资源的可靠性问题,提出了一个包括注册真实性、信任评价和调度契约构成的分层控制模型。
- We make the UDP protocol satisfy the CORBA transport suppose through implement poor reliability control and byte-stream abstract. 通过在UDP协议上层进行了弱可靠性控制和字节流抽象,使UDP协议满足了CORBA网络传输模式中的传输假设,实现了GIOP协议到UDP协议的映射。
- UDT was built in on top of UDP and the introduction of a new congestion control and data reliability control mechanisms. UDT建于UDP之上，并引入新的拥塞控制和数据可靠性控制机制。
- Th e complete digital three class system based on PROFIBUS-DP adapt to high speed ,high reliability control performance in high speed paper machine. 这种基于PROFIBUS-DP的全数字三级控制系统适用于高速纸机的高速度、高可靠性控制性能的需要。
- Stability condition of the proportional control algorithm is given for a fixed target. 针对固定目标，文中给出了比例控制算法的稳定性条件。
- The system is composted of a high accuracy thermocouple and a 8031 single chip computer while adaptive PID control algorithm is employed. 该系统由一个高精度的热电偶和8031单片机组成，采用自适应PID控制算法。
- A new parameters adaptive PID control algorithm is put forward on the basis of Cohen Coon assignment formula. 在Cohe Coon整定公式的基础上 ;提出了一种参数自适应PID控制算法 .
- First, the TCP theory and the key technology of TCP congestion control algorithm are researched in the thesis. 首先,对Internet中传输控制协议的原理以及TCP拥塞控制算法中的关键技术进行了深入探讨和研究。
- First, the jitter control algorithm aims at smoothing the jitter variance with low queueing delay latency. 首先，延迟变异控制机制目标在低延迟代价条件下，减缓延迟变异。
- On this basis, the basic model of main-shaft-less concave printer and ADRC are combined to get a new control algorithm. 在此基础上又将推导出的无主轴凹印机粗基本模型与AD-RC相结合，得出新的控制算法。
- For to evaluate the various control algorithm, Spencer, et al. present a AMD benchmark model. 为了能对各种算法有一个公认的评价标准，美国Notre Dame大学Spencer研究组通过对主动质量驱动(AMD)控制的三层框架模型实验的数据分析，建立了AMD控制Benchmark模型。
- Fuzzy control algorithm is programmed by Borland C++, control of inverted pendulum hardware system is realized. 利用Borland C++编写模糊控制算法程序，实现了倒立摆实物系统控制。
- It is important to develop the ABS ECU, study the control algorithm of ABS, and validate control logic of existing ECU. 它对于ABS ECU的开发、ABS逻辑的研究、验证ECU控制策略的合理性及实用性都是很有效的工具。
- Analying the influence of output transform to NNC control algorithm in neural-PID control. 对神经PID控制中,输出转换成过程对NNC控制算法的影响进行了讨论,使神经PID控制在各种情况下得以正确应用。
