您要查找的是不是：
- In this thesis, the writer takes advantage of ACIS triangulating fuction and takes rounded corner tool for example to discuss calculation and elimination of interference. 利用ACIS的三角化功能,以圆角刀为例,讨论了干涉量的计算与消除,提出了计算刀具外形相对四周三角片的位置。
- It's dangerous to go round corners at speed. 高速转弯很危险。
- A percentage value that represents the height of a rounded corner, from 0 to 100. 表示圆角高度的百分比值,范围从0到100。
- A percentage value that represents the width of a rounded corner, from 0 to 100. 表示圆角宽度的百分比值,范围从0到100。
- The control plan of main drive motor controller and PLC on the AC service system is given out on the analysis of BFP 125 boring tool situation and CNC characters. 本文通过对BFP1 2 5型落地镗床现状的分析 ,结合CNC(ComputerNumeralControl)系统的特点 ,提出了基于交流伺服系统 ,主轴智能马达控制器和PLC的控制方案。
- That was the last bus disappearing round corner,we shall have to hoof it if we want to get home tonight. 最后一班车已转过街角消失了，我们今晚要想回家就得步行。
- I want round corners, not square corners. 我要圆角，不要方角。
- For making boring tools which are used in depth hole boring and facing tools. 制造镗深孔的镗刀和端面车刀。
- After several years to jumbolter research,the hard rocks always present in the soft ones in the wall rock procedure using jumbolter,which results in changing the boring tool during the procedure. 经过几年对锚杆钻机的跟踪研究,发现锚杆钻机在围岩作业中常遇到软岩中有硬岩夹层的现象,造成施工过程经常更换钻具的问题。
- The influence of structure parameters which include diameter of round corner in axis, crankpin length and crankweb width and so on to stress focus place were discussed. 同时还探讨了曲轴的部分结构参数对其应力集中部位的影响，如轴颈过渡圆角半径、曲柄销长度和曲柄臂厚度等。
- Cut rounded corners at one end of the rectangles for the cactus body. 你一定要提高自己，与伴侣坦诚沟通，把事情解决在萌芽状态中。''
- Minor seat damage can be removed by lapping, and major damage can be repaired with portable boring tools. 轻微的阀座磨损可以通过拆卸层叠进行修补，严重的磨损可以采用轻便的钻孔工具进行修补。
- We rounded the corner at high speed. 我们以高速度绕过拐角。
- extension arbor for fine-adjustable boring tool 微调镗刀接长杆
- extension arbor for roughing boring tool 粗镗刀接长杆
- The diagonal dimension of the hexagon parts is controlled by reliable position setting units, small round corner for female module designing and the male module with lateral sharp edge. 凹模型孔设计有一定圆角，凸模带有侧刃，并采用了可靠的定位等措施有效地控制了六角工件的对角线尺寸。
- fine-adjustable bar for boring tool 微调镗刀杆
- A car swung sharply round the corner. 一辆汽车在街角急转弯。
- A Kind of Boring Tool with Inclined Wedge Clamp 一种斜楔机夹镗刀
