您要查找的是不是:
- The sealing design criteria to measure the factors of spiral wound gasket were adopted, based on this bolt loads of flange can be determined by using the new PVRC method. 采用密封设计准则,通过试验确定了金属缠绕式垫片的垫片系数,在此基础上,按照PVRC新方法对法兰螺栓载荷进行了计算。
- sealing design criterion 密封设计准则
- Calcu1ating stress in design criterion of concrete gravity damis based on method of mechanics of materia1s. 混凝土重力坝设计规范的应力计算都是以材料力学法作为基础的。
- Special sealing design can ensure complete sealing in combine place of movement and quiescence. 特殊的密封设计可保证动静结合处的完全密封;
- The design criterion for space-time coded (STC) slow flat Rayleigh fading channels is investigated. 对用于慢变平坦瑞利衰落信道的空时码设计准则进行了研究。
- Especial elastic string types seal design,13 inner pockets,with name card pocket. 独特的松紧带封口设计,13层内页设计,配备名片袋。
- Another aspect of its performance requirement is esthetics. indeed?, there are times when esthetics may constitute a major design criterion. 其次要考虑到美学,这也是功能要求的一个方面。在有些场合,美学的确可能成为设计的主要准则。
- The design criterion for the algorithm is to minimize the error in the set of equations which govern the closed-loop eigenvalues and eigenvectors. 该算法的设计目标是使闭环特征值和特征向量所满足的方程组关于参数摄动误差为最小。
- This paper also describes of design criterion of altimeter orbit,focusing on analysis of T/P altimeter orbit parameters. 通过对多颗高度计轨道设计标准的描述,重点分析了T/P高度计轨道参数的选择。
- TRIZ evolution theory was integrated with reciprocating seal design of servo hydraulic cylinder to predict the future technology,and TRIZ conflicts resolving principles wa. 将TRIZ进化理论与伺服液压缸的往复密封设计融合,预测液压缸往复密封的未来技术结构状态,并利用TRIZ技术冲突解决原理,构思液压缸往复密封的改进设计方案。
- The probabilistic design of LCF for turbine disk was accomplished by modifying the dimensions, in which LCF life reliability was taken as probabilistic design criterion. 以低循环疲劳寿命的可靠度为概率设计准则,对涡轮盘进行反复的设计和计算验证,通过修改结构尺寸完成涡轮盘低循环疲劳的概率设计。
- The working characteristics of side inserted agitators were analyzed first in this paper.Then,them ethods to solve the problem in shaft seal design were presented. 本文分析了侧向伸入式搅拌器的特点,并对轴端密封件的设计提出了可行的设计方案。结果表明该结构有较高的实用价值。
- He describes several of the important design criteria. 他提出了几条主要的设计原则。
- Based on current concrete design criterion, a torsion stiffness formula for composite beams from the cracking stage to the limit stage was proposed for design reference. 基于现行硅结构设计规范,提出了组合梁从开裂到极限阶段抗扭刚度的计算公式,可供组合梁受扭设计参考。
- The design criterion of the MTMD optimum parameters is defined as the minimization of the minimum values of the maximum torsional displacement dynamic magnification factors. MTMD最优参数的设计准则定义为:结构最大扭转角位移动力放大系数的最小值的最小化。
- Objective To design criterion of nurse didactical management mode and improve the nurse clinical practice ability and the clinical nurse didactical level. 目的规范教学管理模式,提高护生临床实践能力和临床护理教学水平。
- Partitioning applied to modules to best meet design criteria. 将软硬件划分应用到模块设计,以便最佳地实现系统的设计指标。
- The job specifications summarized the design criteria. 工作说明书概括总结了设计要求。
- Guideline values for the permissible rotational and circumferential speeds for the different seal designs will be found in the section "Overview". 不同密封件设计的允许转动速度和圆周速度指标值可在“概览”一节中找到。
- The time proven Delta type pressure seal design seals more effectively as pressure increases because the pressure forces the sealing elements into closer contact. 时间证明三角形压力密封设计随着压力的增加密封效果更佳,因为压力迫使密封元件更紧密接触。