您要查找的是不是:
- silica gel leak detector 硅胶探漏器
- The crude oil is chromatographed over silica gel. 粗制油状物用硅胶进行色谱分离。
- Blood Leak Detector LED end plug assy. 漏血检测器插头。
- Blood Leak Detector Photo-diode end plug assy. 漏血检测器光耦插头。
- The purity of isoquercitrin was isolated with a silica gel column. 酶反应产物用硅胶柱层析法提取,可以得到高纯度的异槲皮甙。
- The handpiece cable is made from silica gel tube,soft and durable. 换能器尾线采用进口材料硅胶管,柔软耐用。
- All seals of this machine use the thermostable silica gel (food grade). 该机所有密封件均采用耐高温硅胶件(食品级)。
- There is no possibility to form silica gel in the hard-ened waterglass. 硬化的水玻璃实际上是失水的高模数水玻璃,不可能有硅凝胶生成。
- The specimen was extracted by the macroreticular resin and silica gel column. 样品经大孔树脂柱、硅胶柱分离,然后用TLC进行鉴定合并。
- You may reactivate the silica gel by desorbing the water through heating. 硅胶吸附水份后可通过脱附方式除掉水份而再生。
- Use of the bearing oil leak detector will determine whether or not bearing wear has been uneven. 使用漏油检测装置即可判定轴承磨损是否均匀。
- An electron-capture type halogen leak detector or an NF3 point detector can be used. Refer to the list of monitor suppliers at the end of this section. 可以使用电子俘获型检漏仪或NF3点检漏仪。请参考本文结尾处的监控器供应商列表。
- According to the principal of photoelectricity transform,the authors developed a k ind of photoelectricity leak detector for blast furance dust collection system of bag type. 利用光电转换原理,研制了高炉煤气除尘布袋光电检漏仪。
- The alternative use of buffered silica gel resulted in modest hydrolysis (~5-10%) of the imine. 选用温和的水解导致缓冲硅胶(~5-10%25)的亚胺.
- Aiming at urgent requirement of drilling leakage zone in real time measurement,the development of wireline downhole leak detector has prodigious practice sense. 针对实时测量钻井漏失层位的迫切需要,研制电缆式井下测漏仪具有很大的实际意义。
- METHODS: Alcoholic extraction, silica gel, ODS column chromatography and recrystallization were used. 方法:采用工业酒精提取、胶柱层析、DS柱层析和重结晶等方法。
- Most of the commercially available reversed phase packing materials utilize fully end-capped, high-purity silica gel. 大部分市面上之逆相充填材料利用完善之终结处理,高纯度之矽胶。
- The pastern mold adopts wearable and heat-resistant silica gel, The aluminium mold can come to 200. 胶模采用耐磨热硅胶;外铝模温度可达200。
- Sand should be added carefully, otherwise the silica gel layer will be destructed. 装石英砂时应慢慢加入,不可一次加入而造成柱层破坏。
- Solid conveyor rollers coated with silica gel to bear heavy objects and minimize damage and wear. 输送滚轴全部选用实心滚轴、外部包硅胶,能承受大重量的物体及耐高温。