您要查找的是不是：
- Keywords : deep pit, spatial finite element analysis, failure model. 关键词深基坑，三维有限元分析，破坏模式；
- spatial finite element model 空间有限元模型
- Its finite element model is established. 构造了其有限元模型。
- Studied the strategy of modeling in different phases of SHM, it can be stated that spatial finite spar and beam element model is the appropriate model to aforementioned question. 本文研究了结构健康监测不同阶段的建模策略,认为对于拉索损伤情况下的整桥结构静、动力分析可以采用空间杆系有限元模型进行研究。
- Through mechanical analysis for segmental model of the girder by spatial finite element method (FEM), the mechanism of the two side-boxes of girder under transverse prestressing was obtained. 采用空间有限单元法，建立主梁节段的计算模型，对主梁边箱在横向预应力作用下的受力特性进行分析。
- A static finite element model of an air spring was given. 摘要文中建立了空气弹簧的静态有限元模型。
- spatial finite element physical model 空间有限元实体模型
- This article stagnates the effect question through the spatial finite element method to two cross curve continual steel box Liang shearing force to launch the research. 本文通过空间有限元法对两跨曲线连续钢箱梁剪力滞效应问题展开研究。
- The finite element model of opening gap tantalum thin-walled tube is setup. 为了控制钽薄壁管焊接成形的质量,进行钽薄壁管开口间隙场计算模型的研究。
- spatial shell finite element model 空间板壳有限元模型
- Primary study on the construction of the finite element model of tooth and post-core. 牙齿与桩核三维有限元建模的初步探讨。
- Study Design. In vivo study of a computed tomography (CT)-based nonlinear finite element model (FEM). 研究设计：基于CT的非线性有限元模型(FEM)的体内研究。
- The principles to construct finite element model for modal analysis of the cylinder block have been obtained. 通过研究，得出了建立内燃机机体的有限元模型的一些原则。
- This paper deals with the finite element model of DWX hydraulic prop in aid of Pro/MECHANICA. 本文用Pro/MECHANICA有限元分析软件,建立了柱塞悬浮式液压支柱的有限元模型。
- The finite element model of a small punch test specimen of 1Cr0.5Mo steel is established. 基于小冲孔蠕变试验 ;建立 1Cr0 .;5Mo耐热钢小冲孔蠕变试样的有限元模型。
- The finite element model of the front m ember of one passenger car is created with its CATIA model. 利用轿车前梁的CATIA模型建立其有限元模型。
- Results A three-dimensional finite element model of palatal implant anchorage is successfully constructed, meeting t... 结果建立了符合生物力学研究需要的腭部种植支抗的三维有限元模型。
- Thermal expansion deformation for resistanee spot welding of low-carbonsteel is simulated by an finite element model. 用有限元方法模拟了低碳钢点焊过程的热膨胀变形。
- The finite element models simulating normal, pre- and post-PFO were created. 再者，可产生模拟正常、病患的股骨近端截骨术术前及术后情形的有限元素模型。
- The present finite element model is shown to be reasonable in predicting the ossicular mechanics of human ear. 研究结果表明本文建立的人耳三维有限元模型对研究听骨链声学力学特性是有效的。
