您要查找的是不是：
- specific molding pressure 单位模压力
- The percentage reduction in molding pressure is higher if part becomes thinner when using ICM. 使用射出压缩成型时成品较薄的部分成品压力变化的百分之将提高。
- The relative molecular mass of poly(L-lactide) decreases with the increase of the molding pressure and temperature. 随着压制压力和压制温度的增加， 聚（L-乳酸）的相对分子质量下降。
- It has some guiding significance for improving SMC/BMC molding pressure,sheet flow,product quality and storage life. 本研究对于改进SMC/BMC的成型压力、片材流动、制品质量、模塑料的贮存使用期有一定的指导意义。
- The influence of molding pressure and dunking time on the sulfate attack resistance was studied with experiment. 摘要在不同的试验条件下对抗硫酸盐侵蚀进行试验，研究了成型压力和浸泡时间对混凝土抗硫酸盐侵蚀性能的影响。
- In this paper, the effect of molding pressure on the strength and hydrochloric acid stability of autoclaved lime_stone sand brick is studied. 研究成型压力对蒸压灰砂砖抗压强度和耐盐酸腐蚀能力的影响 .
- The orthogonal experiment indicated that the descending order of factors influencing the properties of the FAC is as follows: molding pressure > heat treatment temperature > heat treatment time > ratio of binder. 正交实验结果表明;影响甲烷体积吸附量的因素由大到小依次为:成型压力>热处理温度>热处理时间>粘结剂的添加比例;并且得出了这种成型活性炭的最佳成型工艺;即:成型压力62.;5MPa;热处理温度250℃;热处理时间90min;粘结剂质量添加比例20%25。
- The results show, when molding pressure changes from 20 MPa to 40 MPa, autoclaved lime_sand bricks get a strength increase of 90.3 percent. Hydrochloric acid stability is also enhanced. 研究表明 ;当成型压力从 2 0MPa升至4 0MPa时 ;蒸压灰砂砖抗压强度可提高 90 .;3%25;耐盐酸腐蚀能力也有所提高
- For PPy/MMT composites, the optimized conditions have reaction temperature, reaction time, the amount of MMT, the amount of oxidizer, the amount and kind of dopant and the molding pressure. 对于聚吡咯／蒙脱土复合体系，其主要优化因素有：反应温度、反应时间、氧化剂的用量、掺杂剂的种类和用量、成型压力和蒙脱土的用量等。
- Education should not be restricted to any one specific age group. 教育不应限制在任何特定的年龄组上。
- He gave us very specific instructions. 他给我们做了非常明确的指示。
- A narrow border, molding, or fillet. 扁带饰窄条，装饰用嵌线或窄带
- There is a specific tool for each job. 各工种配备特定的工具。
- But that all depend on the specific circumstances. 不过，那要看具体情况而定。
- He held fire on specific foreign policy question. 他对具体的外交政策暂不表态。
- Keywords molding process P SMC molding temperature molding pressure cure time; 模压工艺;酚醛SMC;模压温度;成型压力;保温时间;
- There is no specific remedy for the malady. 没有医治这种病的特效药。
- Quinine is a specific for malaria. 奎宁是治疗疟疾的特效药。
- A small molding carved to resemble a string of beads. 串珠饰雕刻成如一串珍珠样的模件
- The architecture specific library code can be found in arch/*/lib/. 与处理器结构相关库代码被放在arch／＊／lib／目录下。
