您要查找的是不是：
- sprayed and fused deposition 喷熔沉积法
- AND FUSED IGNITION SWITCH OUTPUT, CAB CAV 60. 和熔断点火开关输出，CAB槽60。
- Tell me, did Pablo not have caps and fuse? 告诉我，巴勃罗自己没有雷管和导火线吗?
- Automatic temperature control and fuse design. 自动温控及温度保险丝设计。
- Sometimes two ions collide at the center and fuse. 有时两个离子在中心相撞并融合。
- Ni-based and Co-based alloy coatings were made on the Q235 steel substrate by oxy-acetylene flame spraying and fusing. 采用氧乙炔火焰喷熔法在Q235钢表面制备了镍基和钴基合金涂层。
- Fused deposition modeling (FDM), a representative rapid prototyping technology with no use of toxic materials, has been widely used in offices. 摘要熔融堆积成型(FDM)是一种典型的快速成型技术，由于无污染适合办公环境下使用而得到广泛应用。
- The requirement for the property of molding and support materials for Fused Deposition Modeling (FDM) are analyzed. 摘要对熔融沉积(FDM)成型材料、支撑材料的性能要求进行了分析；
- Scan methods of Fused Deposition Modeling(FDM)were analyzed and arithmetic of zoning was put forward. 分析了熔融沉积(FDM)快速成形工艺的扫描方式,建立了分区域穿梭扫描算法。
- The Fused Deposition Modeling (FDM) device has many advantages, such as high accuracy. 熔丝沉积快速成形(FDM)方法是快速成形技术中的一个重要分支。
- The spirit of Barry and Fuseli lives on. 巴里和富塞利的精神常驻人间。
- By using the technology of "element birth and death" in the software of ANSYS, this paper describes the process of Fused Deposition Modeling. 摘要利用ANSYS有限元软件中的“单元生死”技术，对熔融挤压快速成型的成型过程进行模拟。
- Includes spray and direct quenching. 包括喷雾和直接淬火。
- Factors which produce errors in fused deposition modeling (FDM) may include principles, equipment, process and contraction of ABS materials. 快速成型制件产生误差的因素有原理性误差、设备误差、工艺误差及材料收缩引起的误差。
- The spirit of Barry and Fuseli lies on. 巴里和富塞利的精神常驻人间。
- The shaped errors have many forms, including warpage deformation, Stair-stepping effect and so on in fused deposition modeling (FDM). 在熔融堆积成形制造中，形状误差有翘曲变形、台阶效应等形式。
- Abstract With the piston action of unmelted wire , for some Fused Deposition Modeling (FDM) the melted polymer is extruded by the driving force from feeding polymer wire. 摘要 借助未熔丝材的活塞作用，部分熔融沉积造型 (FDM )技术靠料丝插入的驱动力将熔融材料挤出。
- In this paper,the principle of FDM(fused deposition modeling )is brifed,then the factors which influence the precision in maching process was presented in detail. 介绍快速成形技术中的熔融沉积成形的基本原理,分析了在成形过程中,各种因素对精度的影响,并在此基础上,提出了提高成形件精度和表面质量的措施,对熔融沉积工艺有应用价值。
- Police responded with tear gas, pepper spray and water cannon. 警方发放催泪弹、胡椒喷雾和水炮。
- The Fused Deposition Modeling (FDM) device has no laser, so the equipment is cheaper, plus its high efficiency and high accuracy, it is significant to research. 熔丝沉积(FDM)快速成型设备不使用激光器,因此其运行成本低,且其加工效率高,制件的强度大,因此,研究和开发国产化的熔丝沉积快速成型设备具有重要的意义。
