您要查找的是不是：
- spring seat bearing cap 弹簧座轴承盖
- spring seat bearing adjusting nut 弹簧座轴承调整螺母
- spring seat bearing 弹簧座轴承
- Remove the lower insert from the bearing cap. 从轴承盖上拆去下轴瓦。
- A cover bearing and integral seat bearing guide the stem assembly for precise alignment with the seat. 阀盖轴承和整体阀座轴承引导阀杆总成，实现与阀座的精确定位。
- Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware. 产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。
- The three sets of mechanical seal components are as follows: actin ring, quiet ring, push the ring, spring, spring seat, auxiliary ring, ring, such as cards. 这三套机械密封都由如下部件组成：动环、静环、推环、弹簧、弹簧座、辅助密封圈、卡环等。
- Replace seat module with new component by placing into body seat bore. 用新组件更换阀座模块，将其放置到阀体阀座镗孔内。
- Remove shear pin (28) and unscrew bearing cap (16) using a 24ln pipe wrench. Remove "O"rings (25) from bearing cap (16). If they require replacement, remove grease fittings (15). 取走剪销(28);用24"管钳拧下轴承盖(16).;从轴承盖(16)上除去O形圈(25)
- Sagging springs. Spring will sag from overloading or if they have become weak. Loss of the shim from the coil spring seat on the coil-spring suspension will cause the spring to seem shorter and to sag. 弹簧下垂:重载或者弹簧变软均会引起弹簧下垂。螺旋弹簧悬架上弹簧座的垫片丢失,也会引起弹簧变软和下垂。
- High pressure adjusting spring seat 高压调整弹簧座
- bearing cap snap ring replacer set 轴承盖弹簧圈拆装工具
- Low pressure adjusting spring seat 低压调整弹簧座
- This strain of wheat can grow during a cold spring. 这种小麦可以在寒冷的春天生长。
- He nabbed the best seat in the house. 他抢到剧院最好座位。
- Remove both sway bar bearing caps and apply grease to the front pressure points. See pictures below. 取下两个防倾杆盖，并在前压力点涂上润滑油，见下图。
- Bearing caps in the car out of the pass-hole annular trough, grease-filled tank, can improve the sealing effect. 在轴承盖的通孔内车出环形槽，槽中填充润滑脂，可以提高密封的效果。
- He came in and took a seat opposite to me. 他走进来，坐在我对面的座位上。
- I twisted round in my seat to speak to her. 我坐在位子上转过身来跟她说话。
- Roblem of falling chip,tool tipping and big noise are happened during cutting off main bearing caps made of gray cmasting by using combination milling cutters. 采用组合镜刀切断灰口铸铁材质的汽车发动机主轴承盖时,出现工件掉渣、刀具崩刃、噪声大等问题。
