您要查找的是不是:
- symmetric control limits 对称控制限
- NCL: No control limit is allowed. 不允许超出控制界限。
- NCL:No control limit is allowed. 不允许超出控制界限.
- NCL:No control limit is allowed. 不允许超出控制界限。
- Frequency control limits the number of stations you can tune into. 频率控制限制了你们能调谐进的台站数量。
- There is no industry control limits for Copper and Lead in SnAgCu solder pot. 目前行业中没有用于SnAgCu焊料槽中铜和铅的控制极限。
- The recommended control limits for lead is max 1000 ppm, which is in accordance with the RoHs regulation. 铅的推荐控制极限最大为1000 ppm,该值符合RoHs规范。
- Upper and lower statistical control limits that define the constraints of common cause variations. 统计意义上的上限值和下限值,定义数据变量的容许范围。
- For lead-free wave soldering, what is the recommended control limits for impurities such as lead, copper and silver for good control? 要进行无铅波峰焊接,推荐的铅、铜和银等添加剂的控制限制如何才能获得最佳的控制效果?
- Most work with insulation board is indoors and is likely to produce dust concentrations in the atmosphere exceeding the Control Limits. 大部分绝缘板的拆除作业均在室内进行,且产生的环境粉尘浓度很可能超出“控制限度”。
- "Is the microetch rate monitored? Is it under SPC control with calculated control limits and are the charts & actions current? 是否对微蚀率进行监控?其是否有SPC图管控并有正在进行的措施?"
- Dry stripping of bulk insulation and coatings and work other than minor work with insulating board invariably entail temporarily exceeding Control Limits in the area of the work. 干法剥离整体绝缘层和涂层工作不同于绝缘板的小型作业,其作业区中的污染始终会临时超过控制限度。
- Variation beyond a control limit is evidence that assignable causes are affecting the process. 管制界线是从制程的资料来计算,不要和规格界线混淆。
- For complex MMVF removal work, particularly where exposures might exceed the statutory control limits, a written Method Statement must be produced before the work starts. 对于复杂的MMVF拆除作业(尤其在暴露可能超出法定控制限度时),必须在开始作业前提出书面的施工方案。
- The Control Limits are the limits of MMVF concentration in the working atmosphere above which respiratory protective equipment, approved for use with MMVF, must be worn. 控制限度指工作环境的MMVF浓度极限,超过此极限时便必须使用经批准用于MMVF呼吸保护设备。
- The robust normal operating condition model and robust control limits are discussed in detail.The results show that the robust MPLS is resistant to possible outliers. 相对于普通MPLS,鲁棒MPLS在建模数据中存在离群点时仍能给出正确的统计监控模型,降低了建模过程对数据的要求。
- A control chart usually displays a lower control limit (LCL) and an upper control limit (UCL). 注 : 一般而言 , UCL与 LCL 的位置为平均值的正负三个标准差。
- This includes computing and interpreting capability indices, estimating the% failures, control limit calculations, etc. 包括计算和解释过程能力指数、计故障百分率、制限计算等。
- This includes computing and interpreting capability indices, estimating the % failures, control limit calculations, etc. 包括计算和解释过程能力指数、估计故障百分率、控制限计算等。
- Is there a documented system for controlling limited life materials? 对于有使用寿命的原料是否有一个文件化的控制体系