您要查找的是不是：
- tempering process parameters 回火工艺参数
- The production technology of 7050 alloy wire used for rivet was studied. The optimal process parameters for H13 temper and T73 temper rivet were determined. 采用多种配模方案，控制各种不同的加工率，建立工艺多数与组织、性能之间的关系，确定了7050铝合金H13、T73状态铆钉线材的最佳生产工艺制度。
- The structure and process parameters of DSE yarns are analyzed. 分析了DSE纱线的结构和加工性能。
- Gelatinize of process parameters are shown in table 2. 涂胶的不关工艺参数见表2。
- Immediate quenching and tempering process of steel T10 after low temperature salt bath chromizing was studied. 研究了 T10钢在低温盐浴渗铬后直接淬火并回火工艺。
- The relevant suggestion was put forward to strictly control the tempering process and ensure the temperature and heat preservation time exact. 建议加强回火工艺的控制,确保加热温度和时间的准确性。
- The upper stage mixing shaft, the cut reamer big shaft, the up-down body etc. are all passed the aging, quenching and tempering process. 上级搅拌轴、绞龙大轴以及机身上下体等，均经时效、调质、淬火处理；
- Effect of process parameters on curvature of PC bar has been investigated. 研究了工艺参数对国产PC钢棒弯曲度的影响。
- They put forward the optimum tempering process for non-cabide bainite abrasion resisting steel, in addition,introduced the applied effect of ... 提出了适合无碳化物贝氏体耐磨钢的最佳回火工艺,并介绍了无碳化物贝氏体钢的工况及应用结果。
- Process parameters are equally critical to the parts characteristics. 过程参数对于零件的特性同样重要。
- Compared with conventional quenching and tempering process,the effect of austempering on the microstructure and properties of high chromium white cast iron was studied. 对球铁凸轮轴的等温淬火工艺进行了分析,认为产生淬火裂纹的主要原因是:加热炉内的温度过高及等温槽内盐浴老化、等温淬火温度偏低。
- Record and monitor the process parameters and product properties, which may affect the suitability of quality. 对影响质量适宜的过程参数和产品特性进行记录和监控.
- For2Cr13 valve sealing face by double glow plasma W alloying process,carburizing , quenching and tempering process, the results show its machining size is little, its hardness is high and its static pressure lifetime is long. 结果表明经双层辉光离子渗钨、渗碳和淬火回火处理的2Cr13阀门密封面加工量小、硬度高、静压寿命长。
- The optimum operation region of the process parameters is found in the new neural network. 确定金属化工艺中稳定的优化工作区域。
- Special characteristics can include product characteristics and process parameters. 特殊特性可以包括产品特性以及过程参数
- The differences in tempering process between small thin and thick pieces of glass have been pointed out , technical index of heating furnace and wind grating have also been introduced . 说明了小片薄玻璃在钢化生产过程中与厚玻璃钢化的不同,简要介绍了加热炉和风栅等设备的技术指标。
- An example shows that the process parameters can be speedily optimized by the genetic network model, and higher ethylene yield can be obtained. 示例表明：建好后的网络模型可对乙烯生产装置进行快速工艺参数优化，获得较优的操作数据。
- On the basis of the numerical simulation of quenching process,this paper further gives a numerical calculation model of tempering process,emphatically take the stress relaxation into account. 在淬火过程数值模拟基础上,进一步提出了回火过程的数值计算模型,其中着重考虑了应力松弛现象。
- Continual improvement shall focus upon control and reduction of variation in products characteristics and manufacturing process parameters. 制造过程改进必须持续关注于产品特性和制造过程参数的变差的控制和减少。
- Linking Riveting Process Parameters to the Fatigue Performance of Riveted Aircraft Structure. 铆接过程参数与铆接飞机结构的疲劳性能的联系。
