您要查找的是不是:
- The ECS drive shaft equalizes the speed between the drive shaft and the wheel. 精英传动轴均衡的速度之间的传动轴和车轮。
- Each bogie on the driving shaft by a traction motor drive. 转向架上的每个动轴均由一台牵引电动机驱动。
- Hence, the countershaft and all its rigidly connected gears are in motion whenever the drive shaft revolves. 因此,当驱动轴旋转时,副传动轴及与其刚性连接的齿轮都处于运动中。
- Gear A , at the end of the drive shaft, and gear B, on the countershaft, are in constant mesh. 齿轮A位于驱动轴的末端,齿轮B在副传动轴上,它们恒定啮合。
- Self aligning double row spherical roller bearing allows for a higher degree of angular deflection of the drive shaft. 自对正式双列球面滚动轴承允许驱动轴有更高的偏转角度。
- During reassembly, grease the bore of the drive shaft receiving the reduction gear’s output shaft before reinstallation of the clamp ring. 在重组,油脂的膛的传动轴收到减速器的输出轴之前重新安装钳环。
- For SOV energized to counterclockwise drive shaft rotation, reconnect the actuated part to the other end of the drive shaft. 当电磁阀励磁;需要使输出轴向左回转时;只要把输出轴的另一端与被驱动体连接即可.
- Over time, those screws could become loose, possibly resulting in the drive shaft becoming completely detached from the gearbox. 随着时间的推移,这些螺丝会变得松散,可能导致传动轴成为完全脱离了变速箱。
- The screw contact plates on the drive shaft cover plate may not have been manufactured properly, resulting in improperly torqued screws. 钢板螺钉接触的传动轴盖板可能没有生产正常,造成不当扭转螺丝。
- A typical slip joint consists of a hardened, ground splined shaft welded to the drive shaft tube that is inserted into a slip yoke that has matching internal splines. 一个典型的滑关节有一变硬, 地面装以角栓被焊接到被进入一个一直相配内在的云形规的滑轭之内插入的驱动轴管的桥了。
- The drive pinion is beveled at 45 degrees and engages the ring gear, which is also beveled at 45 degrees, causing the ring gear to revolve at 90 degrees to the drive shaft. 该驱动器齿轮是斜45度和参与的齿圈,这也是斜角在45摄氏度,造成齿圈旋转90度的传动轴。
- The drive shaft is useless now. 驱动轴没有用了。
- The driving device includes the drive motor, the drive shaft, the gear housing and the coupling spindles. 驱动装置包括主电机、主轴、齿轮座和联接轴等。
- Unlike traditional JL machine than driving mode is cancelled the drive shaft and gear to be cancelled. 与古板的胶印轮转机比拟,这栽驱不静方法既存消了传不静轴又存消了传不静齿轮。
- The failure of the driving shaft in a hoister is caused by typical brittle fracture under low stress. 卷扬机传动轴的断裂为典型的低应力脆断事故,主要原因是传动轴的组织疏松、晶粒粗大、。
- The driven gear fits its driving gear like a glove. 这个从动齿轮与它的主动轮啮合得非常好。
- The outer tine assemblies adjacent to the ends of the driven shaft are rotatably mounted to the driven shaft. 接近驱动轴两端的外面的打孔针组是可旋转地安装在驱动轴上。
- The load may be reduced by the modification of the front upper conveyor and the driving shaft of the bagging units. 前集荚带与装袋机主动轴经改良后机构之负荷减轻,装袋机无滑动现象,故送荚作业确实无夹裂之虞。
- Select the drive in which you want to store the document. 选择想把文件存储在其中的驱动器。
- We filled the hollow in the drive. 我们把车道上的坑填平了。