您要查找的是不是:
- At last, new failure thickness reduction ratio criterion is used to determine the forming limit of St14 steel based on the numerical system, and the prediction are compared with experimental FLD. 最后,在数值模拟中应用不同形式和参数组合的厚度减薄率判据进行成形极限图预测,并与实验结果进行了比较。
- thickness reduction ratio 变薄系数
- High reduction ratio during primary and secondary crushing stage. 初段,二段等各段破碎均有大破碎比。
- The needed pipe bending moment、wall thickness reduction and ovality of section are known by simulating. 通过模拟,计算管子弯曲变形所需的弯矩,计算管子弯曲部分外壁减薄率和椭圆度。
- The inspiratory expiratory value difference (VD) and area reduction ratio (AR) of bilateral lungs were calculated. 结果各年龄组内男女之间的VD和AR无显著性差异;
- In this article, the influence of thickness reduction due to big deformation for bursting pressure of multilayered cylinder &spherical shells is analyzed.The formula of bursting pressure is found. 用强度削弱系数分析了因大变形引起的壁厚减薄对多层容器爆破压力的影响,导出了多层圆筒形容器与球形容器爆破压力计算公式。
- Through the comparison of numerical simulation value and experiment results, the range of reduction ratio was obtained while the tube forming ideality. 通过数值模拟与实验结果的比较,得出了获得较理想的成形薄壁筒形件时减薄率的选取范围。
- It is found that the tensile strength and the hardness of the specimen decrease, while the elongation and the reduction ratio of area increase. 在平行试样方向上施加强磁场进行退火处理后,球铁的拉伸强度、硬度降低,延伸率、断面收缩率升高。
- The uneven distribution of the reduction ratio of Mo square bar swaged into the circular bar and the Practice calculation method of reduction ratio were discussed. 讨论了钼方坯旋锻归圆前压缩比的不均匀分布情况及其实际压缩比的计算方法。
- process thickness reduction rate 工艺减薄率
- thickness reduction due to punching stretch 冲压拉伸减薄量
- Using lumped mass model, we construct dynamic equation of the flexible arm as well as its Simulink model. Using Simulink model, we analyze how Coulomb friction, motor inertia and reduction ratio of gear affect system performance. 采用集中质量模型建立了柔性手臂的动力学方程及其Simulink模型,利用Simulink模型仿真分析了库仑摩擦力、电机转子惯量和齿轮减速比对系统性能的影响。
- The star cracks in macrostructure appear in some hypo-peritectic continuous cast alloy blooms and these cracks cannot be stock completely by hot rolling reduction ratio, macroetching testing and SEM. 摘要一些亚包晶合金钢连铸大方坯出现低倍星状裂纹,在一定的压缩比下经轧制仍不能完全消除这种低倍缺陷。
- My heart beat thick in the course of the interview. 在面试过程中我的心跳得厉害。
- The star cracks in macrostructure appear in some hypo-peritectic continuous cast alloy blooms and these cracks cannot be stuck completely by hot rolling reduction ratio,macroetching testing and SEM. 一些亚包晶合金钢连铸大方坯出现低倍星状裂纹,在一定的压缩比下经轧制仍不能完全消除这种低倍缺陷。
- Discussion on Thickness Reduction Technology for EB-CCD EB-CCD减薄工艺的讨论
- For a while, the darkling star disappeared behind thick clouds. 隐约出现的星星暂时消失在厚厚的云层後面了。
- She felt that his love had always been covered by thick cloudiness. 她觉得他的爱总是笼罩在浓厚的朦胧中。
- Can't you get it into your thick skull that we can't afford it? 你这个笨脑瓜难道不明白我们买不起吗?
- steering linkage reduction ratio 转向杆系降速比