您要查找的是不是:
- threaded rod support brackets 螺杆支承托架
- Threaded rod, anchor bolt, nut, washer. 牙条,地脚螺栓,螺帽,垫圈。
- The iron rod support the valance is bend in an arc. 挂窗帘上部短幔的铁棍弯成了个弓形。
- Remove nuts attaching GOP to support bracket. 拆下把风栅口面板固定在支架上的螺帽。
- Remove the accumulator from the support bracket. 从支架上拆下蓄压器。
- Remove nut securing pedal shaft in support bracket. 拆卸支撑托架上连接踏板轴的螺帽。
- The iron rod supporting the valances was bent in an arc. 挂窗帘上部短幔的铁棍弯成了个弓形。
- Remove lower bolts that attach bumper to bumper support brackets. 拆去连结保险杆到保险杆支架的下部螺帽。
- All gas line support brackets and tie rods will be galvanized type. 气体管路所有的支架都要镀锌防腐。
- To do so you need to loosen the top 3/8" nut and back it off without unthreading the threaded rod from the spider. 要这样做,就要松开顶部3/8英寸螺母并拿开,不要旋松星轮上的螺纹杆。
- The iron rod supports the valance is bentin an arc. 挂窗帘上部短幔的铁棍弯成了个弓形。
- Conduct maintenance on the equipment and grease the threaded rod and hand wheel nut periodically(every one year or half year). 定期(一年或六个月)对设备进行一次保养,丝杆及手轮螺母部分上油。
- Behind are equipped with wooden backrest with support bracket. 后面都配有木制靠背支架与支持。
- The iron rod supports the valance is bent in an arc. 挂窗帘上部短幔的铁棍弯成了个弓形。
- Position the fog lamp in the support bracket and install the screws. 将雾灯固定于支撑架上并安装螺丝。
- A metal coupling device consisting of an oblong piece internally threaded at both ends into which the two sections of a threaded rod are screwed in order to adjust the tension of the rod. 花篮螺丝,松螺旋扣一种金属的连接环呈椭圆形,两端有内旋螺纹,用来拧紧带螺纹的拉杆的两个部分从而调整拉杆的张力
- Our most competitive products contains Hex bolt, Hex stock set bolt, Hex flang bolt, Carriage bolt, T bolt, U bolt, Machine screw, Auto screw, Threaded rod, and non-standard fasteners. 六角头螺栓,内六角紧定螺丝,六角头法兰面螺栓,马车螺栓,T型栓,U型栓,汽车螺丝,牙条和特种非标准件等。
- It is rack-and-splash open the cabinet composition, and equipped with rolling support brackets. 它由机架和开启式防喷溅的箱体组成,并装有滚动支撑托架。
- The injection machine pushed the knockout plate,and then the knockout plate drove the threaded rod,resulting in the rotation of the threaded core and the auto_demoulding of the plastic part. 模具的特点在于利用注塑机顶出动作,由推板驱动螺杆,经齿轮传动使螺纹型芯旋转,塑件自动脱出。
- Skiving machine includes motor,reducer,electrical box,frame,cage,edge rod support,edge rod,mandrels,mandrel box and pedal. 剥胶机主要由电机、减速器、电气控制柜、机架、机罩、刀杆架、刀杆、剥内胶和外胶的芯棒组、芯棒柜和脚踏开关组成。