您要查找的是不是：
- tinite element model 有限元模型
- Its finite element model is established. 构造了其有限元模型。
- A static finite element model of an air spring was given. 摘要文中建立了空气弹簧的静态有限元模型。
- The finite element model of opening gap tantalum thin-walled tube is setup. 为了控制钽薄壁管焊接成形的质量,进行钽薄壁管开口间隙场计算模型的研究。
- A tapered beam element model is used to simulate the behaviour of a masonry arch bridge with loading. 采用梯形梁单元分析砖石拱桥在载荷作用下的行为。
- Primary study on the construction of the finite element model of tooth and post-core. 牙齿与桩核三维有限元建模的初步探讨。
- Study Design. In vivo study of a computed tomography (CT)-based nonlinear finite element model (FEM). 研究设计：基于CT的非线性有限元模型(FEM)的体内研究。
- The principles to construct finite element model for modal analysis of the cylinder block have been obtained. 通过研究，得出了建立内燃机机体的有限元模型的一些原则。
- Keywords composite materials;heat transfer;tinite element; 复合材料;热传导;有限元;
- This paper deals with the finite element model of DWX hydraulic prop in aid of Pro/MECHANICA. 本文用Pro/MECHANICA有限元分析软件,建立了柱塞悬浮式液压支柱的有限元模型。
- One is taper section 3D beam element model, the other is 3D compounding model with solid element and shell element. 结果表明，在均布荷载与集中荷载作用下箱梁的剪力滞效应明显不同，对于地震时程反应分析而言，采用变截面三维梁单元模型计算效率较高。
- The finite element model of a small punch test specimen of 1Cr0.5Mo steel is established. 基于小冲孔蠕变试验 ;建立 1Cr0 .;5Mo耐热钢小冲孔蠕变试样的有限元模型。
- The finite element model of the front m ember of one passenger car is created with its CATIA model. 利用轿车前梁的CATIA模型建立其有限元模型。
- Results A three-dimensional finite element model of palatal implant anchorage is successfully constructed, meeting t... 结果建立了符合生物力学研究需要的腭部种植支抗的三维有限元模型。
- Thermal expansion deformation for resistanee spot welding of low-carbonsteel is simulated by an finite element model. 用有限元方法模拟了低碳钢点焊过程的热膨胀变形。
- R Frewin,D A Scott.Finite element model of pulsed laser welding[J]. Welding Research Supplement,1999(1). 鹿安理.;焊接过程仿真领域的若干关键问题及其初步研究[J]
- The present finite element model is shown to be reasonable in predicting the ossicular mechanics of human ear. 研究结果表明本文建立的人耳三维有限元模型对研究听骨链声学力学特性是有效的。
- This paper presents the development of a three-dimensional finite element model of central maxillary incisor. 以上颌中切牙为解剖学基础建立了三维有限元模型。
- The finite element models simulating normal, pre- and post-PFO were created. 再者，可产生模拟正常、病患的股骨近端截骨术术前及术后情形的有限元素模型。
- A two-well pumping seepage discrete element model is built and numerically simulated with UDEC. 表明抽水速率界定孔隙压力平均趋近速率:抽水孔间距影响流速;
