您要查找的是不是：
- The variation of ultimate tensile strength with length for amosite crocidolite, chrysotile is shown in Table 2. 10. 铁石棉;青石棉和温石棉的极限抗拉强度随长度的变化情况见表2.;10
- The output parameters of the model are three mechanical properties namely ultimate tensile strength (UTS), yield strength (YS) and elongation (ELO). 模型的输出为三个力学性能指标,即抗拉强度、屈服强度和延伸率。
- The results showed that the UTS(Ultimate Tensile Strength)of composites under tension decreased because of the fracture of zinc. 结果表明:锌的加入使钢/锌复合材料的塑性得到提高,同时其强度与钢相比有所降低。
- Properties determined by mechanical testing, such as yield strength, ductility, ultimate tensile strength, hardness, bendability, impact strength, etc. 由机械试验决定的特性，如屈服强度、延展度、极限抗张强度、硬度、弯曲性、冲击强度等。
- For other alloys, the H2 tempers have the same minimum ultimate tensile strength as the corresponding H1 tempers and slightly higher elongation. 对于其他合金，H2状态有与H1状态相同的极限抗拉强度和稍高的延伸率。
- The effect of the crack eccentricity ratio on the stress intensity factor and the ultimate tensile strength for cracked ductile plates was investigated in this paper. 摘要疲劳裂纹对船舶结构强度具有不可忽视的削弱作用，在过去的研究中，主要从断裂力学的角度对疲劳裂纹应力场进行分析，而对于静态裂纹板的极限强度的探讨相对较少。
- It shows that the ultimate tensile strength and hardness of pure aluminum L2 are improved greatly by ECAP process, the ultimate tensile strength and hardness of L2 alloy is 95% and 70% higher than that of the alloy before ECAP processed respectively. 结果表明,随挤压次数的增加,L2的抗拉强度和硬度得到显著提高,抗拉强度可提高95%25,硬度提高70%25。
- The ultimate tensile strength of each of the composites deformation up to a true strain of 6.4 reach the value of 860 MN/m~2 and 1090 MN/m~2 far higher than the predicated value of rule of mixture. 经真应变为6.;4的形变后;强度分别为860MN/m~2和1090MN/m~2;远远超过混合法则的预测值。
- Compared with die cast, EMC ingots have more fine size of grain, the second phase distributes uniformly and the ultimate tensile strength and elongation have increased by about 15% and 50% respe... 常温抗拉强度和伸长率分别较普通连铸变形镁合金提高了15%25和50%25左右,断口形貌显示其具有韧性断裂的倾向。
- Cu-10Ag and Cu-10Ag-Ce alloys in situ filamentary composites were prepared. The relationships of the ultimate tensile strengths(UTS) and microstructure evolution of the filamentary composites were studied. 制备Cu-10Ag和Cu-10Ag-Ce合金原位纤维复合材料,研究结构变化与应变强化的关系。
- Keywords maraging steel;aluminium alloy;corrosion;ultimate tensile strength; 马氏体时效钢;铝合金;腐蚀失重;抗拉强度;
- Influence of Interfacial Damage on Ultimate Tensile Strength of Cross-Ply Laminates 界面损伤对正交叠层板最终拉伸强度的影响
- Study on Common Calculating Model for Ultimate Tensile Strength of Steel Fiber Reinforced Concrete 钢纤维混凝土极限抗拉强度普适计算模式研究
- Testing the Ultimate Tensile Strength of Prestressing Cable in Core - Cutting Method 用切芯法检验预应力钢绞线极限抗拉强度
- Ultimate Tensile Strength Analysis of Rectangular Plate with Center Through-thickness Crack 具有中心穿透裂纹缺陷的矩形板极限拉伸强度分析
- Keywords Equal channel angular pressing;Armco iron;Route of ECAP;Ultimate tensile strength;Elongation to failure; 等径角变形;工业纯铁;挤压方式;抗拉强度;延伸率;
- Keywords aluminium alloys / Al Si alloy;solidification thermal parameters;dendrite arm space;ultimate tensile strength; 铝合金／铝硅合金;凝固期热参数;二次枝晶间距;极限抗拉强度;
- Study of the Function Relation between Ultimate Tensile Strength of Rolled Pure Titanium Plate and Impurity Content of Its Ingot 纯钛轧制板材抗拉强度与其铸锭杂质含量的函数关系研究
- yield strength (YS) of the steel was 425~460 MPa, ultimate tensile strength (UTS) 505~525 MPa, and ratio of YS-UTS 0.81~0.88, all up to standard. 该钢的屈服强度为425~460MPa,抗拉强度505~525MPa,屈强比0·81~0·88,均达到标准要求。
- The heat treatment improves the tensile strength. 热处理能提高抗拉强度。
