您要查找的是不是:
- Discussion on the wall thickness calculation of gas cylinders in tube trailer 长管拖车气瓶壁厚的计算的探讨
- Reasonable Selection of Different Methods for Cylindrical Shell Wall Thickness Calculation in ASME Code ASME法规中筒体壁厚计算不同方法的合理选用
- Wall thickness calculation and analysis of circle steel coal bucket in electric power plant 电厂钢圆煤斗壁厚计算及分析
- wall thickness calculation 壁厚计算
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- wall thickness calculate 壁厚计算
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- The selection of pipe wall thickness,the calculation and design key points of the melt flow,melt pipe flow pressure fall and melt flow speed in the design of melt pipes were introduced in detail. 介绍了熔体管道设计中管道壁厚选择、熔体流量、熔体管道流动压力降和熔体流速等计算方法和设计要点。
- The heat losses and wall temperature under steady heat conduction of Fiber linings in enamelling furnace are calculated and analysed. The economic lining thickness calculation method is proposed. 分析计算了在稳态导热情况下搪烧炉纤维炉衬不同结构时的散热量和外壁温度,给出了炉衬经济厚度的计算公式和计算方法。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- The simulation results provide basic data for the thickness calculation of oil film considering dynamic load, and valuable theoretical basis for further research on involute gear with unsymmetric teeth and double pressure angles. 仿真结果对考虑动载荷情况下的油膜厚度计算提供了基础数据,为进一步研究非对称渐开线的各种特性提供了理论依据。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm,冷却时间便占10.;8秒。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm,冷却时间是76.;8秒。
- When chilled water is used to cool the mould, cycle time is related to wall thickness as follows. 在冰水冷却的条件下,冷却时间与壁厚有以下的关系。
- The aorta wall thickness (AWT) was measured wiht B-mode echocardiography in 128 patients with primary hypertension. B型超声心动图下测量了128例高血压病患者主动脉壁厚度(AWT),同时检测了血脂指标。
- Centrifugal casting, compact structure, free from pinhole porosity and slag, smooth surface and even wall thickness. 高速离心铸造,组织致密,无砂眼、夹渣,表面光滑、壁厚均匀。