您要查找的是不是：
- The results show that the method can effectively resolve the TWB forming process parameters, and that the weld line movement can be reduced by more than 75%. 优化计算结果表明，该方法能有效求解拼焊板成形过程参数，使焊缝有害偏移量减少75%25以上。
- Keywords tailor welded blank（TWB）square-box;strain path;weld line movement;blank holder force（BHF）;numerical simulation; 拼焊板（TWB）方盒件;应变路径;焊缝移动;压边力（BHF）;数值模拟;
- Research on Welding Line Movement for TWB During Square Cup Drawing 拼焊板在盒形件拉伸过程中的焊缝移动研究
- Weld line movement 焊缝移动
- Weld Area Crack. A crack in or immediately adjacent to the weld line. 焊缝区裂纹。在焊缝线或紧靠焊缝线出现的裂纹。
- THE EQUIPMENTS AND FIXTURE OF WELDING LINE. 焊装线设备及工装夹具
- With Cold Jet, complete weld lines can be cleaned in 25 minutes. 如果使用Cold Jet,彻底清洁焊缝可在25分钟之内完成。
- The machine uses the straight line movement bearing. Causes the machine movement to be smoother. 机器采用直线运动轴承。使机器运行更流畅。
- The maximum value of gapwise-averaged birefringence along the weld line occurred at a small distance from the obstacle. 制品最大双折射值出现在嵌件后一定距离处。
- In the experiments of this research, GTAW butts thin plates of stainless steel and forms a weld line. 摘要本研究以不锈钢薄板在惰性气体钨棒电弧焊对接焊方式进行研究。
- Pinhole. A short unwelded area in the weld line extending through the entire pipe so that fluid will leak out through the area very slowly. 针孔。指焊缝线上位焊接的、贯穿管子整个壁厚的细孔，可导致流体从该孔缓慢漏出。
- All these can be well used for reference to study the cause of molding defects (e. g. warpage, weld line) of ultra-thin wall plastic parts thoroughly. 该结论为深入开展超薄塑件成型缺陷（如翘曲、熔接痕）的形成机理研究提供了有益的借鉴。
- The new method is called welded line tangent method which forms a kinematics model for the robot operating in the bent degree based on the judgment of the tacking system. 该方法是根据焊缝跟踪系统判断焊缝的弯曲程度,确定机器人的运动学模型。
- Introduced planar welding line detect sensor based on GMR. 简述了基于GMR的二维焊缝检测传感器。
- This welding line should be gouged and welded again before tightness inspection. 这条焊缝在密性检查前要碳刨、再焊。
- They also look for potential molding defects, such as gas entrapment, weld lines, shorts and sinks. 也可以看出潜在的模塑缺陷如气体夹陷、熔接线、缺胶和凹陷等。
- A three-dimensional welding line detect sensor based on GMR was introduced. 简述了基于GMR的三维焊缝检测传感器。
- Keywords tailor welded blank （TWB）;drawing;weld line;movement; 拼焊板;拉伸;焊缝;移动;
- rolling bearing for straight line movement 直线运动支承
- Weld lines can take more than two hours to clean completely by using the traditional methods of hand scraping and chemical use. 使用传统手工刮削法与化学品彻底清洁焊接纹需要两个小时以上的时间。
