您要查找的是不是:
- Sometimes all that is left is a skeleton casting with weld metal. 有时所有这些问题都遗留在铸件焊接金属框架里。
- A beam of light produced by a laser can weld metals. 激光器发生的光束可以焊接金属。
- The deposited ferritic weld metal shall not contact the austenitic or high-chromium steel cladding. 熔敷的铁素体焊缝金属不应与奥氏体或高铬钢复层接触。
- Addition of activating agent has no obvious effect on fracture toughness of weld metal. 添加活性剂对焊缝金属的断裂韧性没有明显作用。
- Nb is the element that must be insist in 2.25Cr-1Mo-0.25V steel submerged arc welding weld metal which is demanded in ASME CODE CASE. Nb是ASME标准要求的2.;25Cr1Mo0
- The weld metal is fine and close in structure resulting in goodlooking appearace. 焊缝细密美观;适合全位置焊接;
- Fracture toughness of heat affected zone (HAZ) was between the base metal and weld metal. 焊接热影响区的断裂韧性介于母材和焊缝金属之间。
- D.McKeown, “Hydrogen and its Control in Weld Metal,” Metal Contruction, Vol. 17, No. 10, pp. 655-661, 1985. 张清辉,吴实平,洪波,焊接材料研制理论与技术,冶金工业出版社,第56-58页,民国91年。
- The microstructure of weld metal for MAW is blocky ferrite and a little pearlite, the microstructure in the heat-affected zone is new type bainite. 手工焊焊后不热处理焊缝组织主要为块状铁素体和少量珠光体,热影响区组织为新型贝氏体组织;
- Either coarse or column austenite grain can decrease the toughness of welding metal,and the ways to improve the toughness of wel... 奥氏体晶粒粗大及奥氏体柱状晶都能够降低焊缝的韧性,并提出了改善焊缝韧性的途径。
- The microstructure and wear resistance of the overlaying welding metal of two new types of hardfacing flux-cored wire HDY704 and HDY502 were studied. 对研制的两种硬面药芯焊丝HDY704、HDY502焊态和焊后热处理堆焊层金属的显微组织及耐磨性能进行了研究,探讨了堆焊层金属的磨损机理。
- The results showed that non-metal inclusions in weld metal are round in shape and droplet are chemical reaction products in droplet stage. 结果表明焊缝和熔滴中的非金属夹杂物呈圆球形,它们是熔滴反应区化学反应的产物,属“内生”性质;
- The results of Charpy-V tests have displayed that the weld metal obtains the best toughness at a content of 0.006 wt.% of Zr. 夏比冲击韧性试验显示,锆含量在0.;006%25时焊缝金属韧性最好。
- Addition of activating agent had no obvious effect on fracture toughness of weld metal, but it improved the length of ductile crack propagation. 添加活性剂对焊缝金属的断裂韧性没有明显作用,但对延性裂纹扩展长度有所改善。
- When the oxygen content increases, the weld bead penetration and $ D/W increases sharply while the weld metal width decreases. 随着氧含量的增加, 深宽比和熔深急剧增加, 熔宽减小。
- Welding on large oblique nozzle to shell joint is one of the most difficult points for manufacturing a large gasifier due to special joint shape and high volume of weld metal. 摘要气化炉大型插入式斜接管与筒体的焊接由于接头形状特殊,熔敷金属量大,是气化炉制造的难点之一。
- However, as the chemistry, diffusible hydrogen level of the weld metal, restraint or section thickness increases, the demand for preheat also increases. 然而,由于化学,扩散氢水平的焊缝,克制,或切片厚度的增加,需求的预热也随之增强。
- The art of carving wood, chiseling stone, casting or welding metal, molding clay or wax, etc. into three-dime ional representatio , as statues, figures, forms, etc. 通过对木头、石头进行雕刻,对金属加以铸造、焊接,或对泥、蜡加工制成的三维雕塑作品。
- Microstructure of weld metal is characterized coarsened austenic granular crystal,and the fusion of interface is fine, crystal of overheated zone do not grows up severely. 焊缝为奥氏体组织,呈较为粗大的柱状晶形态,且与母材熔合良好;过热区的晶粒长大不严重。
- The art of carving wood, chiseling stone, casting or welding metal, molding clay or wax, etc. Into three-dimensional representations, as statues, figures, forms, etc. 通过对木头、石头进行雕刻,对金属加以铸造、焊接,或对泥、蜡加工制成的三维雕塑作品。