您要查找的是不是：
- These modular units include analog input multiplexers, analog output devices, "blank" breadboards, signal conditioning modules for thermocouples, and so on. 这些模块化的单位包括模拟输入多路复用器，模拟输出设备，"空白"面包板，热电偶信号调节模块等等。
- The analog input circuitry contains the analog multiplexer, the instrumentation amplifier, and the sample-and-hold circuitry. 模拟输入电路包含模拟多路复用器，仪表放大器，以及采样保持电路。
- Let us compare our unknown analog input signal to a "guess". 现将一个未知的模拟输入信号同一个假定值进行比较。
- The analog input signal is latched on the rising edge of CLK. 模拟输入信号在CLK的上升沿被锁存。
- Figure 7 shows the equivalent circuit of the analog input section. 图7显示模拟输入部件的等效的电路。
- Device where analog output variable is equal to the sum, or a weighted sum, of two or more analog input variables. 一种装置，其模拟输出变量等于两个或多个模拟输入变量的和或加权和。
- The analog data path between the connector and the analog? to? digital converter in the analog input subsystem. 在模拟输入子系统中,模数转换器与连接器之间的模拟数字信道。
- The high level analog input is attenuated before being applied to the same modulator. 经过衰减的高电平信号也可加在同一调制器。
- I / O switch input into (DI), switching output (DO), Analog Input (AI), analog output (AO) and other modules. I/O分为开关量输入（DI），开关量输出（DO），模拟量输入（AI），模拟量输出（AO）等模块。
- An external reference can also be applied and varied from 1 V to +VCC, with an analog input range of 0 V to VREF. 也可以使用外部基准电压，并可在1V至+VCC范围内变化，模拟输入范围为0V至VREF。
- This would also mean it would require a analog input to take a NTC or RTD for this zone to read the temperature. 这同时也意味着它需要一个类似输入以接受该地区的NTC或RTD以读取温度。
- Auxiliary Computer Input Multiplexer 辅助计算机输入多路调制器
- The analog input is continuously sampled by an analog modulator eliminating the need for external sample-and-hold circuitry. 模拟输入由模拟调制器连续采样，因而无需外部采样保持电路。
- For analog inputs, any absolute voltage value above which the analog-to- digital converter cannot distinguish a change. The overload value can be different for plus and minus inputs. 就模拟输入而言，使模数转换器不能区别其变化的超范围的绝对电压值。超载值对于正输入和负输入可能不同。
- The part accepts an analog input range of 0 V to VDD and operates from a single +2.7 V to +5.5 V supply consuming only 9 mW typical. 该器件可接受的模拟输入范围为0V至VDD;采用+2.;7V至+5
- That is to say that it will ignore the “Bad PV” status provided with an analog input and use the actual analog numerical value. 这就是说：它将忽略“工艺测量坏值”状态提供的模拟输入，采用实际模拟数值。
- This allows the widest dynamic input range to the ADC.Thus, the analog input range for the parts are 0 V to VDD.The conversion rate is determined by the SCLK. 基准电压从VDD获得，从而为ADC提供了最宽的动态输入范围，因此，其模拟输入范围为0至VDD。
- The region controller is designed modularly, which is constituted of CPU module, digital input module (DI), digital output module (DO), analog input module (AI). 区域控制器采用模块化设计，由CPU模块、数字量输出模块（DO模块）、数字量输入模块（DI模块）、模拟量输入模块（AI模块）构成。
- Since the analog input voltage and the reference voltage are reversed on alternate cycles, the AD7730 must be synchronized with these reversals of the excitation voltage. 由于模拟输入电压与参考电压是交替循环中颠倒的，ad7730与激励电压同步.
