您要查找的是不是:
- Very low residue and few causticity ,with high-surface insulation resistance value , no need to wash it also can reach the excellent ICT test value . 焊接后残留物少,腐蚀性小,具有极高的表面绝缘阻抗值,无需清洗即可达到极佳的ICT测试性能。
- Measure winding insulation resistance, use 500v Megohmmeter, insulation resistance value shall not less than 0.5 under normal temperature. 测量绕组的绝缘电阻;使用500V兆欧表;常温下绝缘电阻值不应低于0.;5;
- INSTANT OVERLOAD CAPABILITY; WITHOUT ANNUAL SHIFT ON RESISTANCE VALUE. 耐短时间过负载,阻值长时间变化。
- High fracture toughness and insulation resistance. 高断裂强度及绝缘性能。
- This will determine the maximum allowable resistance value of the DB resistor. 这将决定制动电阻最大允许值。
- Measuring insulation resistance for circuit. 电路绝缘电阻测量。
- To measure the hot insulation resistance. 热态绝缘测量。
- The insulation resistance is too low. 绝缘电阻太低。
- High break down voltage and insulation resistance. 高耐压及绝缘性能。
- And shake the electrical insulation resistance measurement, and its value is not lower than 50 megohm. 然后摇测电机的绝缘电阻,其值不低与50兆欧。
- Variance coefficients of BYDV resistance value reduces rapidly when generation added, and BYDV resistance gene purify rapidly. 抗性变异随世代的增加减幅较大,抗病基因纯合较快;
- Shall we start the testing of cold insulation resistance? 冷态绝缘电阻测试是否可以开始?
- Test and mark the resistance value of the old elements having been replaced (with voltmeter and ammeter) and distribute them in low temperature area. 换下来的元件重新(用压表、电流表)测标其电阻值,配阻用在低温区。
- The meter then measures the voltage across the resistance through the same set of test leads and computes the resistance value accordingly. 然后仪表通过同一套测试引线来测量电阻两端的电压,并计算出相应的电阻数值。
- If the insulation resistance is under the numerical value required or the tie-in of the cable loosen or break off,the result will be noted. 如有绝缘电阻低于绝缘要求,或电缆接头松脱、断线,结果将被自动记录。
- The D.C. resistance of each phase is also checked against the calculated resistance value for the stator and for balanced resistance between each phase. 每个相位的直流电阻也经过与定子的设计负载电阻值进行核对,以确认能够在每个相位之间进行平衡。
- Pump before use application megohm table to check the electrical insulation resistance the minimum value of not less than 5 megohm. 电泵在使用前,应用兆欧表检查电机绝缘电阻,其最低值不能小于5兆欧。
- Select resistance values for R1 and R2 such that 20 mA flows through each LED. 为R1和R2选择合适的阻值,使得通过每一个二极体的电流都为20毫安培培。
- Among it the sensing surface of sensor should be established Whetstone Bridge, when the pressure is increased, resistance value of each bridge arm takes place change. 其中传感器感压面有惠斯顿电桥,当增加压力时,电桥各桥臂电阻值发生变化。
- The temperature characteristics of insulation resistance of capacitor covers. 电容器盖板绝缘电阻的温度特性。