您要查找的是不是：
- Install the high pressure relief valve in the compressor manifold fitting. 在压缩机歧管配件里安装高压释放阀。
- For pressure relief you turn the opening valve against clockwise direction. 压力释放时,逆时针旋转开口阀。
- Install a 125 PSI pressure relief valve in the cold water supply line. 在冷水供应管道上安装一个125psi的减压安全阀。
- Pressure relief devices protect storage tanks against overpressure hazards, you must know their set points. 压力释放装置用于防止超压的危险,你必须清楚它们的设定值。
- Do not walk on the top surfaces of the Powerbloc panels, rupture points for pressure relief. 不要在开关柜泻压顶板上行走。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必须正确安装,使得降温减压安全阀和排水管道都能够完全排泄。
- Building valves - Combined temperature and pressure relief valves - Tests and requirements. 建筑阀门。温度和压力组合安全阀。试验和要求。
- Temperature and Pressure Relief Valve is required, but may not be factory installed. 需要降温减压安全阀,但可能不在工厂安装。
- Note: The installation of a separate pressure relief valve is necessary for installations using gas shutoffs. 注意:采用燃气关闭阀,有必要安装独立的压力安全阀。
- Use regulators and pressure relief devices when connecting cylinders to circuits having lower pressure service ratings. 当把钢瓶连接到较低额定工作压力的回路上时，要使用调整器和减压装置。
- You must make provisions for pressure relief protection of your plumbing system and components. 此时就必须采取措施进行压力释放，以保护管道系统和部件。
- By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve. 通过这种功能，det系列将系统压力保持在温度压力安全阀的排放设置下。
- Therefore, the spacecraft must have a facility with "pressure relief" feature and restore function. 因此，航天器上必须有一个设施具有“泄压”功能和恢复功能。
- Multiple pressure relief devices are installed on these tanks to protect against overpressure. 在这些储氦罐上安装了多样减压装置，以防止过压。
- It can simplify the fire supply system of highrise building by applying pressure relief valve to vertical compartment. 采用减压阀对高层建筑物的消防给水系统进行竖向分区 ,可以简化系统。
- An ASME Section IV certified pressure relief valve shall be installed on each boiler as noted. 正如以前所提到，每个锅炉都应该安装一个ASME第四节认证的压力安全阀。
- Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure. 每个热水供暖锅炉都必须配置压力安全阀,其设置的泄压压力必须小于锅炉的最大工作压力。
- DO NOT tamper with the electronic control board, temperature sensors, heating elements, electrical connections, or temperature and pressure relief valve. 不要篡改电气控制板，温度感应器，加热元件，电气连接，或降温减压安全阀。
- Temperature and pressure relief valve properly installed with a discharge line plumbed to an open drain and protected from freezing. 正确安装降温减压安全阀，并配置排泄管引导至一个敞开的排水口，并确保不会被冻结。
- It mainly consists of blind cap, blind base, unblanking mechanism, seal ring, tumbler, safety lock plate, pressure relief. 它主要是由盲板盖、盲板座、开启机构、密封圈、转臂、安全锁板、泄压装置构成。
