您要查找的是不是：
- oil pressure relief valve spring 油压安全阀簧
- Due to the release of pressure when removing the cover, the relief valve spring may eject quickly. 因为在拆卸阀盖时松开压力，安全阀弹簧可能会快速弹出来。
- Install the high pressure relief valve in the compressor manifold fitting. 在压缩机歧管配件里安装高压释放阀。
- Install a 125 PSI pressure relief valve in the cold water supply line. 在冷水供应管道上安装一个125psi的减压安全阀。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必须正确安装,使得降温减压安全阀和排水管道都能够完全排泄。
- Remove the relief valve cover, stem/diaphragm assembly, and relief valve spring. 拆卸安全阀阀盖，阀杆/隔膜总成，和安全阀弹簧。
- Temperature and Pressure Relief Valve is required, but may not be factory installed. 需要降温减压安全阀,但可能不在工厂安装。
- Note: The installation of a separate pressure relief valve is necessary for installations using gas shutoffs. 注意:采用燃气关闭阀,有必要安装独立的压力安全阀。
- By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve. 通过这种功能，det系列将系统压力保持在温度压力安全阀的排放设置下。
- It can simplify the fire supply system of highrise building by applying pressure relief valve to vertical compartment. 采用减压阀对高层建筑物的消防给水系统进行竖向分区 ,可以简化系统。
- An ASME Section IV certified pressure relief valve shall be installed on each boiler as noted. 正如以前所提到，每个锅炉都应该安装一个ASME第四节认证的压力安全阀。
- spring loaded pressure relief valve 弹簧加载的压力泄放阀
- Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure. 每个热水供暖锅炉都必须配置压力安全阀,其设置的泄压压力必须小于锅炉的最大工作压力。
- Remove the relief valve spring. 拆卸安全阀弹簧。
- DO NOT tamper with the electronic control board, temperature sensors, heating elements, electrical connections, or temperature and pressure relief valve. 不要篡改电气控制板，温度感应器，加热元件，电气连接，或降温减压安全阀。
- Temperature and pressure relief valve properly installed with a discharge line plumbed to an open drain and protected from freezing. 正确安装降温减压安全阀，并配置排泄管引导至一个敞开的排水口，并确保不会被冻结。
- Temperature and pressure relief valve properly installed with a discharge line run to an open drain and protected from freezing. 正确安装降温减压安全阀,并配置排泄管引导至一个敞开的排水口,并确保不会被冻结。
- NOTE: 15" diameter chambers are standardly furnished with a pressure relief valve, factory set at 60psi to protect the chamber from excessive pressure. 注：在压力安全阀上，15英寸直径的腔室室标准配置，工厂设置是60psi，以保护腔室不会出现压力过大现象。
- Periodic discharge of the temperature and pressure relief valve may be due to thermal expansion in a closed water supply system. 在一个封闭的水供应系统中，热膨胀可能导致降温减压安全阀的周期性排泄。
- In order to prevent misuse, and some special pressure relief valve and the special connection between the cylinder mouth. 为了防止误用，有些专用减压阀与钢瓶之间采用特殊连接口。
