您要查找的是不是：
- Further opening the throttle valve activated the main fuel jet. 当节流阀进一步打开时,主喷口开始工作。
- Air inlet throttle valve with pneumatic actuator and positioner. 空气进气节流调节阀：带有气动定位和执行机构。
- The adjusting of screw prevents the throttle valve from moving to the fully closed position. 调节螺钉防止节气门运动到全关闭位置。
- Finally, an appropriate throttle valve was chose to serve the superfluid helium system. 最终确定了一个适合该超流氦系统的较为理想的节流阀。
- A throttle valve control device is composed of a stator core with a solenoid and a rotor carrying a throttle valve. 一种节流阀控制装置，包括一个带螺线管的定子铁芯和一个带节流阀的转子。
- Enough air-found mixture can seep around the throttle valve and through the idle system to maintain the dieseling. 围绕在节气门处有足够的空气燃料混合气经怠速系统泄漏过来助长了熄不了火现象。
- Reduced pressure near the partially closed throttle valve caused the fuel to flow from the idling jet into the intake air. 由于部分关闭的节流阀附近的压力下降,燃油由怠速喷口喷入吸进的空气。
- The sleeve also rises up the shaft, and when it rises beyond a certain point, it operates a throttle valve lever, and so reduces the flow of steam. 套筒也随之顺轴上升。而当套筒升过一定的点时，套筒就会带动一个节流阀的阀杆进入工作，这样就能减少蒸汽的流量。
- Whereas, the optimal heat rejection pressure in the expander cycle is different from that of in the throttle valve cycle. 但是，膨胀机循环的最佳高压压力与节流阀循环的最佳高压压力不同。
- When the compressor and the expander efficiencies are given, the optimal heat rejection pressure in the CO2 throttle valve cycle is greater than that of in the expander cycle. 当压缩机和膨胀机的效率一定时，CO2节流阀循环的最佳高压压力比膨胀机循环的高。
- Weighing hopper is lodged on 3 load cells. The amplifier, feeding device with dust collar, magnetic vibrator, pneumatically operated throttle valve shutter are included. 称重仓带有3个传感器。系统包括：放大器、进料装置和收尘包、振动器、放料气阀。
- Through fuel pumps,plus a throttle valve of statistical instruments,minus contained,thus allowing detection instruments in different load performance parameters. 通过油泵、节流阀对被测机具进行加、减载,从而可以检测机具在不同载荷下的性能参数。
- In the exploration and development of high-pressure reservoirs, many dangerous cases even accidents of blowout happen because of the throttle valve failing. 在高压油气藏的勘探开发中，多次因节流阀失效而发生井喷失控险情，甚至导致井喷事故。
- The application and working process of throttle valve in injection mold of unbalanced cavities were introduced,and the key points of designing throttle valve was analysed. 介绍了节流阀在非平衡型腔注射模中的应用及模具工作过程,并分析了节流阀的设计要点。
- A systematic study was performed on the extruder set via analyses of the factors such as feeding, screw speed, throttle valve, screen pack changer, die plate and pelletizer, aimed at saving energy. 选择进料状况、螺杆转速、节流阀、换网器和模板及切粒机等因素对挤出机机组的影响进行了系统分析、研究,发现这些因素对挤出机的负荷和能耗影响较大。
- The carbon-dioxide swinging rotor expander was designed and developed to replace the throttle valve in order to reduce the loss of throttling. 摘要设计开发了二氧化碳摆动转子膨胀机，代替节流阀减小节流损失。
- stacked unidirectional throttle valve 叠加式单向节流阀
- stacked double directional throttle valve 叠加式单向节流阀
- Cause analysis of the water cooled wall tube burst focused on irrational points of design,excessive thermal loading,changes of coal category,burner defects and deposits in throttle valves. 着重从锅炉设计不合理、热负荷过高、煤种变化、燃烧器的缺陷及节流阀结垢等方面分析了水冷壁爆管的原因,指出必须进行锅炉改造。
- BOWDEN CABLE PULLEY FOR THROTTLE VALVE 节气门拉索滑轮
