您要查找的是不是:
- Wheel hub drive by spur gears 直齿圆柱齿轮轮边传动
- Spokes radiate from a wheel hub. 轮条从轮轴向四周伸出
- ZHEJIANG YUELING WHEEL HUB MAKING CO., LTD. 浙江省跃岭轮毂制造有限公司。
- Wheel hub units, wheel bearing, gear, tensioner, pulley. 汽车轮毂轴承,轮毂单元,圆锥轴承,齿轮,皮带轮,涨紧轮。
- The slight decrease in the spools length is to accommodate the flange gasket, approximately 1/8". 稍微增加短管长度以适应法兰垫圈,大约1/8英寸。
- The urethane liner extends over the flange face to serve as the valve's flange gasket. 这种氨基甲酸乙酯延展覆盖到法兰表面,起到阀门法兰衬垫的作用。
- We are looking for a car wheel hub,supplier for our European and US markets. 求购欧洲车和日本车的汽车轮毂;请发详细的产品资料和报价.
- Note: The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 注意:闸阀的法兰垫圈螺栓在安装期间应该重新紧固,因为在库存和运输时这些螺栓可能会松懈。
- The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 在安装期间,闸阀上的法兰垫圈螺栓应该重新紧固,因为在库存和运输时螺栓可能会松懈。
- Installation Note: The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 安装注意事项:在安装期间,闸阀上的法兰垫圈螺栓应该重新紧固,因为在库存和运输期间螺栓可能松动。
- Seat Face: Negates need for flange gaskets. 阀座表面:不需要使用阀兰垫圈。
- INSTALLATION NOTE : The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 安装注意事项:在安装期间,闸阀上的法兰垫圈螺栓应该重新紧固,因为在库存和运输期间螺栓可能松动。
- It can fully inflate in less than 30 milliseconds as it deploys out of the steering wheel hub. 它由方向盘中间向外展开,其完全充气时间不超过 30 毫秒。
- Founded in 1988, we mainly produce and distribute wheel hub bearing and wheel hub unit of "UUU" and "NTP" brand. 主要生产和经营UUU牌和NTP牌汽车轮毂轴承、轿车轮毂轴承单元。
- Wheel hub unit, driveshaft speed is expected to become the new pillars of Products. 轮毂单元、等速驱动轴有望成为新的支柱产品。
- The part of the axle ex-tending beyond the bearing assembly is either splined or tapered to a wheel hub and brake drum assembly. 的部分车轴前往往超出了轴承装配要么花键或锥形的轮毂和制动鼓组装。
- Such as the steering idler and the upper and lower control arms; removal and replacement of springs; removal and replacement of wheel hub and drum; and so on. 如转向转轴和上下控制臂,拆卸和更换轮彀和制动鼓等。
- Put the wheel hub on a turning device, make it whirl on the strength of one constant bending moment, make hub bear a whirling bending moment constantly. 将轮毂置于一旋转的装置上,使其可在一恒定不变的弯矩作用下旋转,使轮毂始终承受一个旋转弯曲力矩的作用。
- water pump outlet valve flange gasket 水泵出口阀法兰垫片
- Put the wheel hub on a turning device ,make it whirl on the strength of one constant bending moment ,make hub bear a whirling bending moment constantly. 将轮毂置于一旋转的装置上,使其可在一恒定不变的弯矩作用下旋转,使轮毂始终承受一个旋转弯曲力矩的作用。