您要查找的是不是：
- steering column jacket oil hole cover 转向轴套油孔盖
- oil hole cover [化] 给油口盖
- A kind of Rotary cultivator shell, it includes shell with transmission shaft axis hole and set oil hole, set oil hole end has end cover , magnet is in this end cover . 一种旋耕机机壳，它包括带有传动轴轴孔及放油孔的壳体,放油孔端头设有端盖，在该端盖内设有磁铁。
- Centerline discharge pump casings are not acceptable. The pump casing shall have an integrally cast hand hole supplied with a hand hole cover. 中心线排放泵壳是不可接受的。泵壳上应该具有整体铸造的探孔,并配置探孔罩盖。
- She then guided me to a shabby hole covered by collapsed buildings. 后来奉顺带我到一处颓圮的洞穴,四周被半倒的建筑物覆盖着。
- Centerline discharge pump casing s are not acceptable. The pump casing shall have an integrally cast hand hole supplied with a hand hole cover. 中心线排放泵壳是不可接受的。泵壳上应该具有整体铸造的探孔,并配置探孔罩盖。
- There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings. 轴瓦内表面的不承担载荷部分开有油槽，润滑油通过进油孔和邮沟流进间隙。
- The oil hole is small and deep, so it is very difficult to machining. and we will try to take the broken aiguille out, and end it as soon. 因为油孔又小又深，加工难度本身很大，我方将尽快把断在里面钻头取出来就算完工。
- The fracture of stuffing box was caused by fatigue, which resulted from the maximum stress concentration on the centripetal border of the oil hole. 结果表明：材料成分和显微组织均符合要求；裂纹起源于输油孔的侧壁；填料盘的失效模式为疲劳失效，内压在填料盘内部输油孔上产生的应力集中导致了填料盘的疲劳失效。
- The hand hole cover shall be constructed of the same material as the pump casing and shall have surfaces which match the internal casing contours to minimize turbulence and localized wear. 探孔罩盖结构材料应该与泵壳完全相同,其表面应该与泵壳内部轮廓线相匹配,以减少由于扰动和定位造成的磨损。
- This article introduces mainly calculation of a slanting angle of crankshaft clamping with the analysis method in machining crankshaft oblique oil hole. 主要介绍在加工发动机曲轴斜油孔时,用解析法计算曲轴装夹时所倾斜的角度。
- At its largest this year, the ozone hole covered more than 15 million square kilometers. 今年臭氧空洞最大的时候曾达到1500万平方公里，
- The centre console suffers the most with the ashtray and cubby hole covers feeling extremely flimsy. 中心控制台最蒙受烟灰缸和小房间洞盖子感到极端轻而薄之苦。
- FAW TOYOTA engine company crankshaft product line uses carbide tool and MQL technique to process crankshaft oil holes. 一汽丰田(长春)发动机有限公司曲轴生产线采用硬质合金钻头并配合半干式加工(MQL)技术加工曲轴油孔。
- crank case inspection hole cover 曲轴箱检查孔盖
- brake drum inspection hole cover 闸轮检查孔盖
- Improvement in Piston Pin Boss Oil Hole Machining 活塞销座油孔加工方法改进
- Research on location of the distribution oil hole 配油孔定位研究
- He slicks his hair down with oil every day. 他每天搽油把头梳得光溜溜的。
- The oil leaked away because there was a small hole on the tank. 没渗出来了，因为没箱上有一个小洞。
